Roper One Speed Automatic series washing Machine Errors
PROBLEM CAUSE SOLUTION
Washing machine leak
NOTE. After
Checking them,
Check your home
Plumbing. Fill the hoses not tight. Tighten the hoses. See the Installation section.
Instructions.
Fill the hose washers incorrectly. Wipe (move) washers. See
Instructions for installation.
Incorrect drain hose
Or off. Squeeze the drain hose.
The drain is clogged. Clean the sink. Sink and pressure pipe
Must be able to handle 17 gallons
(65 liters) of water per minute.
The tank moved forward during unloading,
Forcing the water to deviate from the bath ring. Make sure that the bath is centered to
Starting washer
The knot is uneven, causing water to deflect
Bath opening Make sure that the front feet are installed and
The nuts are tight. Washer level.
Filling or spraying the rinsing deviates
Load. Washer overloaded or loaded
Unbalanced. Redistribute the load or reduce
The size of the load.
Washing machine will not be
Draining / rotating
The drain hose is clogged. Unscrew the hose. See the Installation section.
Instructions for correct installation
Drain hose.
The lid is open. Close the cover.
The end of the drain hose is larger than
72 inches (191 cm) above the floor. Lower drain hose.
Too much detergent is excessive foam. Use less detergent
Low voltage or using an extension cord Check the electrical source or call
an electrician. Do not use the extension
Cords
Wet Loads
Incorrect cycle for washing the load. Select a cycle with a higher rotation
speed.
Cold rinses. Cold rinses leave the cargo more damp than
Warm rinses. This is normal.
Puck continues
To fill / drain or
Tight cycle Upper drain hose is lower than water
Level in the puck. Pick up the drain hose. It should be
Above for proper operation.
The drain hose is too tightly inserted into the riser.
Disconnect the drain hose
Safe landing. See the Installation section.
Instructions.
Drain the hose that is embedded in the discharge pipe. • Do not plug the drain hose with a tape.
The hose needs an air gap
Washer Noise
The load is not balanced. Redistribute the load.
The washer is not flat. Washer level. Resetting the rear alignment
legs. See the Installation Instructions.
The nuts on the front legs are not tightened. Tighten the nuts.
Yellow transport strap with pin pins
Not completely removed. See the Installation Instructions.
Drives after draining and
Before the back. This is normal.
Not fill / wash / mix
Or the wrong temperature.
The power cord is not connected. Connect the power cord.
Timer (Cycle Control)
Not lined up.
Turn the timer knob to the right slightly
And pull to start.
The screens of water intake valves are cleaned.
The water is off. Turn on the water.
Hot and cold hoses are turned over. Reverse hoses
The inlet hose is twisted. Straighten the hose.
Stopping the washing machine
The power cord is not connected. Connect the power cord.
No power when connected. Check the electrical source or call
an electrician
The fuse or circuit breaker is switched off. Replace fuse or reset circuit
switch. If the problem continues,
Call an electrician.
Using an extension cord. Do not use extension cords.
The dial of the timer is not aligned. Turn the timer to the right slightly
And pull to start.
The timer knob did not pull out. Install and remove the handle.
The machine is overloaded. Wash smaller loads
The water level seems
Too low or washer
Not completely filled out. The top of the mixer is much higher
Than the highest water level. This creates
The perception of the washer is not filled. This is normal.
Washer for washing machine
The curved bath stretches forward when unloading. Push the bath to the center
beginning.
The impasse moves.
This is normal.
The unit is not installed. Make sure that the front feet are installed
And the nuts are tight. level
Washer. Reset the rear leveling feet.
See the Installation Instructions.
Residue or lint
At startup Incorrect sorting. Sorting of linters (towels, chenille)
From villi (corduroy,
synthetics). Also sort by color.
Overload.
Lint can be captured by the load if
Overloaded. Wash smaller loads
Paper or cloth in pockets Clean the pockets before washing.
Not enough detergent. Use a sufficient amount of detergent to keep
The detergent does not dissolve. Use a heater for washing water than 70 ° F
(21 ° C).
Rinse with water colder than 70 ° F (21 ° C) Use warm water for washing than 70 ° F
(21 ° C).
Tear overload. Incorrect use of the washer. Loads must move freely during
wash. Wash smaller loads.
Improper use of chlorine bleach. Do not pour chlorine bleach directly
during. Wipe off the bleaching liquids.
Unclean bleach will damage the fabric.
Sharp objects not removed from pockets;
The fasteners are not fastened. Wash pockets before washing.
Zipper before washing
Elements damaged before washing.
Stitches before washing
Stains during loading Incorrect use of fabric softener. Dilute the fabric softener and add
Wash part of the cycle only. Not
Fabric softener on clothes.
Iron (rust) in water. Install the iron filter.
Insufficient amount of detergent causing soil
For reprecipitation Use a sufficient amount of detergent to remove soil
And hold it in the pause state.
Dye transfer due to non-sorting of goods
Correct Sorting of dark clothes from white and
lights
Dye transfer due to non-unloading
Puck quickly unload the puck as soon as it is
Stops.